ADC Kentrox ISDN NT1 1010 Specifiche Pagina 240
- Pagina / 552
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
5-8
Reference Guide
Model No.
Running Head
CPU Card User Screens and Settings CPU Card
Table 5-3. Print Alarm Screen Option Settings and Defaults
Notes:
1. The Print Alarms option must be
off
if TCP/IP is
on
.
2. The choice of “empty” will eliminate that element from the NMS report.
PRT ALARMS
The Print Alarms option allows you to choose a remote device for alarm condition reporting.
The system uses the modem (if present) on the Interface card to call a remote device or
Network Management System. The system sends the alarm information for all alarm filters
set to
Report
in the Alarm Filters screen. Refer to Chapter 4
System Configuration and
Operation
.
Set the Print Alarms setting to
off
to disable all external alarm-generated messages. Choose
direct
to send all alarms reported since the last report cycle to a local device through the DB-9
computer port of the Interface card. The
modem
setting sends all alarms reported since the
last report cycle to a remote dial-up device through the modem port.
The remote device may be any asynchronous ASCII device that can accept lines of text up to
80 characters long. It must support XON/XOFF flow control and be capable of attaching to an
asynchronous dial-up modem. Figure 5-4 shows an OOS alarm reported to a remote device.
The remote device’s modem must be compatible with CCITT V.22bis and support connections
at 2.4 kbps. Set the remote modem for auto-answer mode.
Both the remote device and
modem should be set for 8 data bits, 1 stop bit and no parity.
Parameter User Options Notes Default
PRT ALARMS off direct modem 1 off
PRT Phone# telephone number (up to 14 numbers)
PRT RETRY 1 to 60 1
PRT ATTEMPTS 1 to 99 1
PRT MAJ&CRIT 1 to 500 1
PRT MIN&INFO 1 to 32000 1
ELEMENT 1 alarm model address time severity
number empty
2number
ELEMENT 2 alarm model address time severity
number empty
2alarm
ELEMENT 3 alarm model address time severity
number empty
2 model
ELEMENT 4 alarm model address time severity
number empty
2address
ELEMENT 5 alarm model address time severity
number empty
2 time
ELEMENT 6 alarm model address time severity
number empty
2 severity
- Integrated Access System 1
- System Reference Guide 1
- Publication 999-001989 1
- Product Description 3
- New System Features 3
- Features in this Release 3
- System Cards 4
- Voice Cards 5
- Data Cards 6
- Optional Features 7
- User Card Reference Guides 9
- Model No 10
- Running Head 10
- WARNING! 11
- Grounding 12
- FCC Part 68 Information 15
- CE Marking 16
- Declaration of Conformity 16
- United Kingdom 18
- UK Compliance Statements 18
- Contents 21
- Chapter 1 43
- System Overview 43
- Chassis Types System Overview 44
- System Overview Chassis Types 45
- Power Supply and 51
- Ringer Supports 51
- Chapter 2 55
- Applications 55
- 2.2 Sample Applications 56
- 2.3.3 E&M Card 58
- 2.3.5 TR008 Application 60
- 2.4.1 HSU Card 62
- 2.4.2 HSU Application Example 64
- 2.4.3 SRU Card 64
- IAD w/ SRU 65
- 2.4.4 FRAD Card 66
- 2.4.5 OCU-DP Card 67
- 2.4.6 BRI Card 69
- 2.4.6.1 BRI Card Models 70
- 2.4.7 DSO-DP Card 71
- T1/E1 carrier 74
- . . . . . 75
- Provider 79
- Backbone 80
- 2.6.6 PRI to FXS termination 83
- 2.6.7 Routing Capabilities 83
- 56/64Kbps 93
- 2.9 ATM Server Card 95
- ATM Server Card Applications 96
- Applications ATM Server Card 97
- ATM Edge Switch 97
- 2.10 Routing Server 99
- Routing Server Applications 100
- Reference Guide 101
- Router Router 104
- System Installation 107
- Chapter 3 107
- 3.3.2 Pre-Installation Tips 108
- 3.3.4 Installing the Chassis 110
- Holes for Tabletop Attachment 111
- Inches 10 15 3/4 2 113
- Centimeters 25 38 2 5 113
- CAUTION! 114
- 3.5 Ringing Generators 116
- Side in a A/C Environment 121
- Model: IMACS/800 123
- AC “third wire” Ground 127
- 3.7 Powering Up the System 128
- 3.8.2 CPU Card (8803) 129
- 3.8.4 Server Cards 129
- 3.8.5 User Cards 130
- Chapter 4 131
- 4.3.1 Registration 132
- 4.3.2 Logging Into the System 137
- 4.4 System Screens 141
- 4.4.3 Server Card Status 143
- 4.4.4 Card Main Screens 144
- 4.5 Card Configuration 146
- 4.6 Reinitializing the System 148
- 4.7 Alarms 150
- 4.7.2 Alarm Filter Settings 152
- 4.7.3 Alarm Modifiers 155
- 4.7.4 Alarm Cutoff (ACO) 155
- 4.7.6 Alarm Handling 156
- 4.11 Cross-Connecting (XCON) 158
- 4.12 System Level Maintenance 158
- 4.12.2 Zipping the System 160
- 4.12.3 Debugging the System 161
- 4.12.4 Registering the System 161
- 4.12.6 TFTP Backup for 5.x.x 162
- 4.12.7 TFTP Restore for 5.x.x 163
- 4.12.8 ASCII Backup Procedure 164
- 4.14 CPU Switching 167
- 4.15 Time Slot Assignment 167
- 4.16 Assigning Time Slots 168
- 4.16.3 Cross-Connect Model 171
- CIRCUIT ID 179
- Figure 4-28. WAN Unit Options 181
- Figure 4-30. Test Options 183
- 4.19 Cross-Connect Actions 192
- Tx ABCD BITS 197
- 4.21.1 WAN Link to WAN Link 207
- Figure 4-52. The TADS screen 209
- 4.21.4 Monitor Circuit 210
- 4.21.5 Split Circuit 213
- 4.21.6 Release 215
- Action Function 217
- 4.24 Redundant Operations 222
- 4.25 Power Supply Redundancy 222
- 4.26 CPU Card Redundancy 223
- 4.27 WAN Card Redundancy 225
- 4.28 ADPCM Card Redundancy 229
- Chapter 5 233
- CPU Card 233
- 5.3.1 CPU Card Main Screen 235
- PRT PHONE# 241
- PRT RETRY 241
- PRT ATTEMPTS 241
- PRT, MAJ&CRIT 241
- PRT MIN&INFO 241
- 5.4 TCP/IP Network Management 242
- HOST IP STATE 245
- HOST IP ADDR 245
- DEFAULT IP SLOT 247
- RPT1 COMMUN STR 249
- RPT2 IP ADDR 249
- RPT2 COMMUN STR 249
- RPT3 IP ADDR 249
- RPT3 COMMUN STR 249
- Frames Transmitted 253
- Frames Aborted on Transmit 253
- 5.4.1.3 IP Parameters 253
- Default TTL 253
- 5.4.1.6 UDP Parameters 259
- Packets From Above 259
- Packets Sent 259
- 5.4.1.8 SNMP Parameters 261
- PDUs Sent 261
- Traps Sent 261
- Sessions Closed 261
- TX Wait for Buffer 261
- 5.5 IP Packet Routing 262
- CPU Card IP Packet Routing 263
- IP Packet Routing CPU Card 264
- 5.5.1 nX64 Screen 270
- 5.6.1 Equipment Requirements 274
- 5.6.2 Laptop Setup 274
- 5.6.3 Upgrade Preparation 275
- 5.7.1 CPU Swap 276
- 5.8 CPU Card Error Messages 280
- 5.9 CPU Card Troubleshooting 280
- 5.10 CPU Card Specifications 281
- Chapter 6 283
- Interface Card 283
- 6.2.1.3 External Sync Panel 285
- 6.3.2 Call Profile Screen 295
- CALLED # 297
- CALLED # TYPE 297
- CALLED # PLAN 297
- CHANNEL RATE 297
- RATE MULTIPLIER 297
- PRESENT. INDCTR 299
- SCREEN. INDCTR 299
- BCAST. PHONES 299
- 6.3.4.1 Identification 301
- 6.3.4.2 Network Priorities 302
- 6.3.4.4 Terminal Security 302
- AT Command Function 303
- 6.3.5 Ports Screen 304
- PROTOCOL 305
- HANDSHAKE 305
- 6.3.7 Using the Node Port 307
- 6.5.1 User Interface Problems 308
- Chapter 7 313
- WAN Card 313
- Figure 7-2. WAN-U DUAL Card 315
- 7.3 WAN Module Descriptions 317
- Side View 325
- Remove all plastic standoffs 325
- 7.4.1 T1 CSU and DSX Settings 330
- Table 7-6. AIS/ALM Settings 335
- LOCAL LB 336
- ESF/NMS RP 337
- 7.4.2 E1 CEPT/HDSL Settings 340
- EER THRHD 351
- RDNT RULES 351
- 7.4.4 Cross-Connect (XCON) 353
- 7.4.5 Performance Data 355
- 7.4.7 Test Screen 360
- 7.4.8 Adtran E1/HDSL Screen 363
- QLTY LP1 365
- QLTY LP2 365
- (local 15-minute interval) 365
- Loopbacks toward Master OEM 371
- Module (or HiGain HLU) 371
- Loopbacks toward Slave OEM 371
- Module (or HiGain HRU) 371
- LB STATE 373
- *REMOTE* 373
- 7.5 PARS Screen 374
- WAN Card PARS Screen 375
- PARS Screen WAN Card 376
- 7.5.1 Implementation of PARS 378
- 7.5.3 One Link is Lost 380
- 7.6 WAN Card Error Messages 388
- 7.7 WAN Card Troubleshooting 388
- 7.8 WAN Card Specifications 389
- E1 Interface 391
- E1 HDSL Interface 391
- Chapter 8 393
- 8.3.2 Voice Diagnostics 395
- 8.3.3 Data Diagnostics 396
- 8.4.1 Circuit Diagnostics 398
- Figure 4 401
- Figure 1 401
- Figure 2 401
- Figure 3 401
- 8.6 Performance Monitoring 403
- Appendix A 405
- A.2 Standards Compatibility 406
- Interface Cards 407
- WAN Cards 407
- E&M Cards 409
- FRAD Cards 409
- OCU-DP Card 409
- HSU Cards 411
- SRU Card 411
- A.3 Chassis Standards 412
- A.3.2 Chassis Power 413
- A.3.3 Environment 413
- A.3.4 Equipment Handling 414
- A.3.6 Cable/Power Connections 415
- A.3.7 Mounting 415
- A.3.8 Number of Slots 416
- Manufacturer Part Number 419
- A.5 Card Specifications 420
- A.7 FCC Requirements 425
- A.8 UK Requirements 426
- A.9 Year 2000 Compliance 427
- Appendix B 429
- Error Messages 429
- Appendix C 449
- C.2 Interface Cards 450
- Using the COM2 Port 451
- Figure C-2. RJ48 (COM2) Jack 451
- Using the Management Port 455
- C.2.2 INF+M Card (8923) 458
- Using the Modem Port 459
- Figure C-9. MODEM Jack 459
- WAN Port Connections 463
- Figure C-13. NET Jack 463
- C.2.3 INF Card (8924) 465
- C.3 Alarm Cards 468
- C.3.2 ALR 4+3PF Card (8402) 469
- C.3.3 ALR 28+14 Card (8403) 470
- Voice Circuit Connection 473
- Figure C-20. RJ-11 Jack 473
- C.4 HSU Cards 474
- Pin Function Direction 475
- C.4.2 HSU-T V11 Card (8203) 476
- C.4.3 HSU 35 Card (8212) 478
- C-25 shows these jacks 479
- RS-366 Jacks 481
- C.4.5 HSU-T V35 Card (8214) 482
- C.4.8 HSU Card Cables 488
- HSU CARD DCE PROVIDES CLOCK 489
- RS530 V.35 RS449 489
- C.5 SRU Cards 490
- C.6 OCU-DP Cards 494
- C.6.2 OCU-DP 5 Card (8241) 496
- C.6.3 OCU-DP 10 Card (8246) 498
- C.7 FRAD Cards 500
- C.8 DS0-DP Cards 502
- C.9 B7R Cards 504
- C.10 BRI Cards 506
- C.10.2 BRI-SC U*8 Card (8261) 507
- C.10.3 BRI-ST*8 Card (8262) 508
- Port Designation Pin # 509
- C.10.5 BRI-2 U*8 Card (8264) 511
- C.10.6 PM-IOR Card (8280) 512
- 2. Not connected 513
- C.11 Server Cards 514
- C.11.2 ACS-ATM Card (8820) 515
- C.11.4 IPR 10BT Card (8831) 517
- C.12 E&M Cards 518
- C.13 FXS Cards 526
- C.13.2 FXS 2W*8-6 Card (8219) 527
- C.14 FXO Cards 528
- C.14.2 FXS Coin Card (8149) 529
- C.14.3 FXO Coin Card (8159) 530
- C.15 P-Phone Cards 531
- Glossary 533
Prodotti e manuali riguardandi Networking ADC Kentrox ISDN NT1 1010
Networking ADC Kentrox ISDN NT1 1010 Specifiche
(24 pagine)
(24 pagine)
Daktronics AF-3180-64-R,A manuály
Uživatelské manuály a uživatelské příručky pro Monitory Daktronics AF-3180-64-R,A.
Poskytujeme 1 manuály pdf Daktronics AF-3180-64-R,A ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commenti su questo manuale